Storage tank double-walled, 9000 L, diesel, heating oil, bio-diesel
Note: The illustrations may also contain accessories and special equipment which are not included in the standardscope of delivery because of example illustration.

Item no.: KTD-9000-D

KTD-9000-D
Double-walled day tank for supplying aggregates with fuel or lubricating oil.

- Material: steel S 235 JR
- Certified acc. German DIBT: Z-38.12-23
- Volume 100% filling height appr.: 9,350 ltr.
- Volume: 95% filling height appr.: 8,900 ltr.

Standard dimension:

- Length appr.: 3,400 mm
- Width appr.: 2,000 mm
- Width total appr.: 2,030 mm
- Height appr.: 1,500 mm
- Height total appr.: 1,950 mm
- Weight appr.: 1,840 kg (without equipment, empty)

Category: storage tank double-walled (950 L - 50.000 L)

Prices visible after login
Available

Delivery status: 6-8 weeks

Packing flat

The stated packaging flat rate applies exclusively to standard packaging and exclusively to truck transport. Seaworthy packaging will be charged separately.

  • without flat-rate packaging fee for exclusive delivery of accessories
  • packaging flat
    Fix costs for packing of of tanks over 2000 ltr. up to 5000 ltr.
Coating (inside) in m²

The antistatic inner coating is a corrosion protection for resistance to stress caused by media such as kerosene or other fuels with a low discharge capacity and a tendency to static charging.

Special options

additional equipment

  • Suction pipe 1" flanged with foot valve
    - for tank height up to 2000mm
    - flanged
    - diameter: 160mm
    - 4-hole flange with welded 1" socket
    - seal
  • Suction pipe 2" flanged with foot valve

    - foot valve
    - flanged
    - diameter 160mm
    - 4-hole flange with welded bush 1?
    - seal

  • Filling socket DN 50 45°

    Filling socket DN 50

    - filling pipe closure 2" x 2 1/2"
    - 1 x angle 2", 45° female
  • Filling nozzle DN 80 with tank truck coupling

    Filling nozzle DN 80 with tank truck coupling

    -father coupling VK 80Ms. DIN 28450
    -blind cover MK 80M
    -brass tanker chain L=300mm

  • Krampitz Sealfix M 10 ml
    Krampitz Sealfix M
    • Dichtmittel
    • Schraubensicherung
    • 10 ml
Sensors: Content display
  • Level Sensor
    - Resistance reed chain actuated by float magnet
    - Output signal: 4-20 mA
    - tank height: 1500 mm
    - Reduction PE 2" to 1.1/4
    - Connector plug M12
  • Level control module in percent 1K

    Analysis module for the recording of percentage values of the tank level

    - Display in percent
    - Configuration of up to 4 switching points
    - In addition a  4 - 20 mA sensor is required
    - The 4 - 20 mA signal can also be routed to other analysis modules
    - Not required for container with PLC

Sensors: Level indicator
  • Level sensor (float switch) (Bio-)Diesel

    - Output: Reed Contact
    - Switching function: 1 closer, falling level
    - Ambient temperature range: -5 ° C to + 70 ° C
    - Medium temperature: -5 ° C to + 70 ° C
    - with floater made of stainless steel
    - adjustable height 50 - 2.000 mm
    - cable length 5 m
    - dry run protection

  • Level sensor (float switch) (Bio-)Diesel

    - Output: Reed Contact
    - Switching function: 1 closer, falling level
    - Ambient temperature range: -5 ° C to + 70 ° C
    - Medium temperature: -5 ° C to + 70 ° C
    - with floater made of stainless steel
    - adjustable height 50 - 2.000 mm
    - cable length 5 m
    - dry run protection

  • Level sensor (float switch) (Bio-)Diesel

    - Output: Reed Contact
    - Switching function: 1 closer, falling level
    - Ambient temperature range: -5 ° C to + 70 ° C
    - Medium temperature: -5 ° C to + 70 ° C
    - with floater made of stainless steel
    - adjustable height 50 - 2.000 mm
    - cable length 5 m
    - dry run protection

  • Level indicator (float switch) lubricating oil/H?O
    - floater made of stainless steel
    - adjustable height 50 - 2.000 mm,
    - Cable length: 5,000 mm
    - for lubricating oil and water
    - T: max 40 ° C
    Only delivery!
  • 1-fold cable screw
    - Reducer G2" male - M16x1.5 female
    - Cable screw M16x1,5 AG PVC
    - 1x Sealing ring
    - Only delivery!
  • 2-fold cable screw

    - Red. "G2" AG
    - 2x M16 x 1.5 IG PE
    - 2x Cable gland M16x1.5 AG PVC
    - 1x seal ring 58 x 2,5 mm
    - Only delivery!

  • 4-fold cable screw

    - Red. "G2" AG
    - 4x M16 x 1.5 IG PE
    - 4x Cable gland M16x1.5 AG PVC
    - 1x seal ring 58 x 2,5 mm
    - 2x Seal plug
    - Only delivery!

Sensors: overfill protection

Equipment required under water law to limit the max. filling level when filled by a tanker or using fixed piping.

  • limiting level transmitter Type GWG 12-K1
    - only for diesel / heating oil with CE-mark
    - with 1,5 m cable
    - Reduction 2" x 1" (AG/IG)
    - Mandatory for tanks with a volume of 1000 litres or more
  • Overfill prevention Type 76 A

    Overfill prevention Sensor

    - Type 76 A, Sensor length 200 mm
    - Connection: G 3/4" male
    Only delivery!
  • Level Limiter Type: NB 220 H

    Level Limiter Type: NB 220 H

    - with potential free changer
    - Supply: 230 V, 50 Hz
    - not to be mounted directly on the tank for media such as kerosene or bioethanol

    Only delivery!
  • Overfill protection confirmation box

    - Mounting plate
    - Voltage 24 V/DC
    - Housing protection grade IP 54
    - switch-off-electronic
    - Receipt key
    - Flash light 1 Joule
    - Horn 95 Decibel
    - Road tanker connection 907-Z
    - not to be mounted directly on the tank for media such as kerosene or bioethanol

    Only Delivery!
Sensors: Tank heating

Plant equipment for reliable prevention of paraffin excretion of the fuel at falling temperatures and maintenance of the pump and nozzle viscosity of the oil in the intake area (frost-free from 8°C to 12°C).

  • Tank heater type TH 372 up to 8000 ltr.
    - approved for diesel and heating oil EL
       - (hazard class AIII according to VbF)
    - TÜV approval
    - Power: 1,5 kW
    - Voltage: 230 V 50 Hz
    - with 1-pole controller approx. 8-12°C
       - (switches on below 8°C and off above 12°C)
    - with 1-pole limiter approx. 55°C
       - (Safety switch, switches off above 55°C if controller is defective!)
    - incl. 1-fold cable gland (AM-986)
    - Red. G2" AG -M16x1,5 IG PE
    - Cable gland M16x1.5 ET PVC
    - Sealing ring
    - Connecting cable 6 m oil-resistant with rubber protective contact plug
    Attention: Only use the heater in liquid!
  • Magnetic fixing for tank heating
    Magnetic fixing for tank heating
    consisting of:
    - 2x magnet 42mm x 9mm
    - 2x pipe clamp 40mm - 45mm
    - 2x countersunk screw and nut M6
Pumps

Z-PK is a combination of a hand vane pump and a centrifugal pump in one housing. In the event of a complete network failure, refilling of the day tank is also ensured manually with the hand vane pump.

  • Pump set 230 V

    Pumpenkombination für Heizöl und Diesel

    bestehend aus:

    • 1x Kreiselpumpe
    • Förderleistung: 5 bis 50 ltr./min.
    • 1x Handflügelpumpe
    • Förderleistung: 15 ltr./min.
    • Tropfwanne Typ Z-PK-2100
    • Korrosionsschutz
    • Nicht montiert, nur geliefert!
  • Pump set 400 V

    - Medium: diesel / heating oil
    - 1x centrifugal pump:
       - Delivery rate: 5 to 50 ltr./min.
       -Pumping height: 46 to 10 m Fl.s.
       -Pumping pressure: 3 bar
       -setting pressure: 3 bar
       -Suction height: 6 m
       -voltage: 400 V
       -current consumption: 2.0 A
       -frequency: 50 Hz
       -Electric power: 0.6 kW
       -speed: 2,900 rpm
    - 1x hand wing pump:
       - delivery rate: 15 ltr./min.
       - delivery head: approx. 10 m Fl.s.
       - suction height: 4 m
    - 1x twin pump body:
       - 4 pieces mounting holes
       - diameter: 11 mm
       - Two inlets DN 25 / 1" on the suction side
       - Outlet on the pressure side DN 20 / 3/4
       - Connection internal thread for:
       - 2 ball valves 1" for suction side
       - 1 ball valve 3/4" for pressure side
       - 1x drip tray
       - completely assembled and piped on console
    - Corrosion protection 2-component paint in RAL 7032

    Not assembled, only delivered!

  • Centrifugal pump Type PK-80-015

    Kreiselpumpe

    • Fördermenge:
    • 43 ltr./min. bei 5 m FLS
    • 11 ltr./min. bei 30 m FLS
    • Förderhöhe: 46 - 10 mWs
    • Spannung: 230 V
    • Motorleistung: 0,55 kW
    • Nennstrom: 5 A
    • Motorschutzart: IP 44
    • Korrosionsschutz
  • Centrifugal pump 43-11 ltr., 400 V

    Centrifugal pump

    • Flow rate:
      • 43 ltr./min. at 5 m FLS
      • 11 ltr./min. at 30 m FLS
    • Voltage: 400 V
    • Electrical power: 0,6 kW
    • Rated current: 2 A
    • Connections:
      • suction line: 1"
      • pressure line: 1"
    • Weight: 10,8 kg
  • Drip tray for centrifugal pump

    Drip tray for centrifugal pump for separate wall mounting

    Corrosion protection:

    • 2K paint in RAL 7032
  • Drip tray for hand vane pump
    - for separate wall mounting
    - Corrosion protection K paint in RAL 7032
  • Drip tray for hand vane pump
    - for separate wall mounting
    - Corrosion protection K paint in RAL 7032
  • Drip tray for hand vane pump
    - for separate wall mounting
    - Corrosion protection K paint in RAL 7032
  • Hand crank pump
    - Material: aluminium
    - Connection: 1".
    - Delivery rate: 100 ltr/min
    - Delivery head approx.: 10 m
    - Suction height approx.: 4 m
    - Corrosion protection: 2-component paint in RAL 7032
    - No documentation available!
Manual

Manual by letter at the owner's expense

  • Manual by letter at the owner's expense
    The operating instructions, data sheets and certificates are available in paper form delivered by letter.
Price as configured:

Description

KTD-9000-D
Double-walled day tank for supplying aggregates with fuel or lubricating oil.

- Material: steel S 235 JR
- Certified acc. German DIBT: Z-38.12-23
- Volume 100% filling height appr.: 9,350 ltr.
- Volume: 95% filling height appr.: 8,900 ltr.

Standard dimension:

- Length appr.: 3,400 mm
- Width appr.: 2,000 mm
- Width total appr.: 2,030 mm
- Height appr.: 1,500 mm
- Height total appr.: 1,950 mm
- Weight appr.: 1,840 kg (without equipment, empty)

Standard Equipment

1x AM-595 Burst protection Ø 115 mm
1x AM-001 Float level indicator type 1000
1x AM-350 Vakuum leak detector Eurovac-HV (AC 230V)
1x X-S-2-022 Filling pipe 2" for tank height 1500mm
1x AM-090 Type plate
1x AM-947 Dust cover 1" yellow, screwable
9x AM-948 Dust cover 2 "yellow conical
2x AM-941 Blanking plug 2" screwable PE with seal
1x AM-960-21P Reduction 2 "x 3/4" PE black, Krampitz
1x AM-960-22P Reduction 2 "x 1" PE black, Krampitz
1x AM-911 Ventilation nozzle DN 50 250mm
1x BE2 Manual by download

- Inspection opening DN 600
- Entry steps in the tank for inspection
- Crane eyes
- Access ladder outside
- Connection on top: 9x 2"
- Connection on top: 1x flange Ø160 mm, 1" socket
- Top connection: 3x 3/8" for vacuum leak detector
- LAZ mounted on the roof for indoor installation

Corrosion protection:

- inside: raw, oiled
- outside: coating L-A-1, RAL 7032

Documentation:

- Test documents in German (Sending by mail)
- Test certificate
- Overview drawing
- Building inspection approval
- Operating Instructions Tank
- Datasheets / Operating Instructions for accessories
- Certificates WHG and ISO 9001
- additional documentation in Paper, on CD or by mail will be charged extra
Volume: 9000 ltr.
Type: Storagetank
Medium: Diesel-biodiesel Heating oil
Material: Steel
Wall Design: double walled